View TSM100_348984.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TSM100
SINGLE OPERATIONAL AMPLIFIER AND SINGLE COMPARATOR
OPERATIONAL AMPLIFIER
s LOW INPUT OFFSET VOLTAGE : 0.5mV typ. s MEDIUM BANDWIDTH (unity gain) : 0.9MHz s LARGE OUTPUT VOLTAGE SWING : 0V to
(VCC - 1.5V)
s INPUT COMMON MODE VOLTAGE RANGE
INCLUDES GROUND
s WIDE POWER SUPPLY RANGE : 5 to 30V
2.5 TO 15V
s ESD PROTECTION : 2kV
COMPARATOR (OPEN COLLECTOR)
D SO8 (Plastic Micropackage)
s INPUT COMMON MODE VOLTAGE RANGE
INCLUDES GROUND
s LOW OUTPUT SATURATION VOLTAGE :
250mV @ Io = 4mA PIN CONNECTIONS (top view) DESCRIPTION The TSM100 is a monolithic IC that includes one independent op-amp and one independent comparator. This device is offering space and cost saving in many applications like power supply management or data acquisition systems. ORDER CODE
Part Number TSM100I Temperature Range -40C, +105C Package D *
Ground : 4
Amp Output : 1 Amp Input - : 2
8 : Vcc 7 : Comp Output
Amp Input + : 3
+
6 : Comp Input -
5 : Comp Input +
D = Small Outline Package (SO) - also available in Tape & Reel (DT)
July 2001
+
1/5
TSM100
ABSOLUTE MAXIMUM RATINGS
Symbol VCC Vid Vi Toper Tj Tl Rthja Supply Voltage Differential Input Voltage Input Voltage Operating Free-air Temperature Range Maximum Junction Temperature Maximum Lead Temperature (10 seconds maximum) Thermal Resistance Junction to Ambient Parameter Value 32 32 -03. to +32 -40 to +105 150 260 175 Unit V V V C C C C/W
ELECTRICAL CHARACTERISTICS
Symbol ICC Parameter Total Supply Current Vcc+ = 5V, no load Vcc+ = 30V, no load Min. Typ. 0.9 Max. 1.4 1.8 Unit mA
2/5
TSM100
OPERATIONAL AMPLIFIER VCC+ = +5V, VCC = Ground, V o = 1.4V,T amb = 25C (unless otherwise specified)
Symbol Vio Parameter Input Offset Voltage Tamb = 25C Tmin. Tamb Tmax. Input Offset Voltage Drift Input Offset Current Input Bias Current Large Signal Voltage Gain VCC = 15V, RL = 2k, Vo = 1.4V to 11.4V Supply Voltage Rejection Ratio VCC = 5V to 30V Input Common Mode Voltage Range VCC = +30V - see note 1) 50 65 0 Min. Typ. 0.5 7 2 20 100 dB 100 (VCC+) -1.5 30 150 Max. 3 4 V/C nA nA V/mV Unit mV
DVio Iio Iib Avd SVR Vicm
V dB
mA
CMR Isource
Io Isink
Common Mode Rejection Ratio
Output Current Source VCC = +15V, Vo = 2V, Vid = +1V Short Circuit to Ground VCC = +15V Output Current Sink Vid = -1V, VCC = +15V, Vo = 2V VCC = +15V, Vo = 0.2V High Level Output Voltage VCC+ = 30V Tamb = 25C, RL = 2k Tamb = 25C, RL = 10k Low Level Output Voltage RL = 10k Slew Rate at Unity Gain Vi = 0.5 to 3V, VCC = 15V RL = 2k, CL = 100pF, unity gain Gain Bandwidth Product VCC = 30V,RL = 2k, CL = 100pF f = 100kHz, Vin = 10mV Total Harmonic Distortion f = 1kHz AV = 20dB,RL = 2k, VCC = 30V CL = 100pF, Vo = 2Vpp Equivalent Input Noise Voltage f = 1kHz, Rs = 100 Vcc = 30V
65
20
85
40
mA 40 60
10 12
20 50
mA A V
VOH
26 27
27 28 mV 5 15 V/s
VOL SR
0.2
0.4 MHz
GBP
0.5
0.9 % 0.015
THD
en
nV/Hz 40
1. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC+ - 1.5V. But both inputs can go to Vcc+ +0.3V without damage.
3/5
TSM100
COMPARATOR VCC+ = +5V, VCC = Ground,Tamb = 25C (unless otherwise specified)
Symbol Vio Iio Iib Avd Vicm Input Offset Voltage Tamb = 25C Input Offset Current Input Bias Current Large Signal Voltage Gain VCC = 15V, RL = 15k, Vo = 1V to 11V Input Common Mode Voltage Range 1) Output Sink Current Vid = -1V, Vo = 1.5V Low Level Output Voltage Vid = -1V, Isink = 4mA High Level Output Current Vid = 1V, Vcc = Vo = 30V Response Time RL = 5.1k to VCC+ 2) Large Signal Response Time Vi = TTL, Vref = +1.4V, RL = 5.1k to VCC+ 0 6 16 Parameter Min. Typ. 1 5 25 200 (VCC+) -1.5 Max. 5 50 250 Unit mV nA nA V/mV
V
mA mV
Isink
VOL IOH tre trel
250 0.1
400 nA s
1.3 ns 300
1. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC+ - 1.5V. But either of both inputs can go to 36V without damage. 2. The response time is specified for a 100mV input step with 5mV overdrive. For larger overdrive signals, 300ns can be obtained
4/5
TSM100
PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO)
Millimeters Dim. Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S 0.1 0.65 0.35 0.19 0.25 4.8 5.8 1.27 3.81 3.8 0.4 4.0 1.27 0.6 8 (max.) 0.150 0.016 Typ. Max. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 45 (typ.) 5.0 6.2 0.189 0.228 Min. 0.004 0.026 0.014 0.007 0.010
Inches Typ. Max. 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.197 0.244 0.050 0.150 0.157 0.050 0.024
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. (c) The ST logo is a registered trademark of STMicroelectronics (c) 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom (c) http://www.st.com
5/5

▲Up To Search▲

Price & Availability of TSM100

	To Download TSM100 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .